Welding Rhepanol Seams and Roof Details
A reliable Rhepanol roof depends on compatible seams, upstands and junction details. FDT documents hot-air welding for the specified PIB seam areas on hfk and hg. Procedures and checks depend on the membrane variant.
ROOF MEMBRANES · RHEPANOL (PIB)
A reliable Rhepanol roof depends on compatible seams, upstands and junction details. FDT documents hot-air welding for the specified PIB seam areas on hfk and hg. Procedures and checks depend on the membrane variant.
Clean and dry the seam in accordance with FDT, use the prescribed hot-air welding procedure, carry out required trial welds and inspect completed joints. Do not treat Rhepanol as generic PVC or EPDM seam work; FDT says solvent welding is not possible for hfk or hg.
Why Rhepanol welding is product-specific
FDT describes homogeneous hot-air welding of suitable hfk and hg seam zones. The hfk weldable edge is part of the product, while hg has a different glass-fleece-reinforced construction.
PVC welding specifications and EPDM seam tapes are not automatic substitutes. Compare hfk, hg and PVC membrane seams.
Prepare and clean the joint
Welding surfaces must be clean and dry. Where specified, clean the joint zone with Rhepanol seam cleaner and allow it to evaporate. Pay particular attention to aged or contaminated membranes.
Use suitable hot-air equipment, pressure rollers and trial welds as instructed. Keep current installation documentation available on site.
Record trial weld results and site conditions rather than relying solely on one machine temperature setting.
Welding conditions, laps and T-joints
Use the FDT-specified lap and seam widths for the exact membrane and method. Temperature and travel speed depend on weather, equipment and the membrane condition; there is no safe universal setting.
T-joints may require particular treatment to avoid capillary action. FDT describes careful preparation of the centre membrane edge and inspection of seam lines. See the general lap guide, then verify the PIB-specific dimensions.
Edges, upstands and penetrations
FDT offers Rhepanol-laminated metal, connection collars, termination profiles and other compatible accessories. Roof-edge or wall junctions must be designed for the selected system and substrate.
Estimate separate quantities for corners, edges, outlets and wall junctions. Our roof-edge quantity guide helps count materials, but generic bitumen or PVC profiles are not automatically approved for PIB.
Verify FDT/QRS accessory compatibility and wind resistance for the actual roof.
Inspection and the bill of materials
Inspect continuous welds, corners, upstands and penetrations before further roof layers conceal the waterproofing. Record defects and repair by the prescribed technique. Access becomes more difficult on ballasted roofs.
List seam cleaning, welding, detail strips, trial welds and repair labour separately in the material schedule. For green roofs, inspect before covering the membrane.
Estimate Rhepanol roof area, rolls and materials
Select PIB (Rhepanol), verify the hfk roll format and enter actual supplier purchase prices. DakCalc provides a provisional material estimate, not an approved laying plan, wind design or FDT system certification. Verify the delivered hg roll format and configuration.
Open the DakCalc calculator →More Rhepanol guides
Also useful in the knowledge hub: roofing system comparison, calculating membrane laps, roof-edge trims and corners.
Frequently asked questions
Can Rhepanol be hot-air welded?
Yes. FDT documents product-specific hot-air welded seams for hfk and hg.
Can Rhepanol hfk be solvent welded?
FDT indicates solvent welding is not possible for hfk; use the approved hot-air procedure.
What hot-air temperature should I use?
There is no universal setting. Follow FDT guidance, actual weather and trial welds.
Sources and technical documents
Product dimensions, adhesives, fixing methods and examples do not certify a roof assembly. Check current FDT/QRS guidance, local rules, project-specific wind design and your supplier quote before ordering.