Bonding Rhepanol: Approved Adhesives and Substrates
Bonding Rhepanol is not a matter of spreading arbitrary roof adhesive across a PIB sheet. FDT defines specific products, substrates and methods. The full hfk assembly must be approved for the intended partial or other
ROOF MEMBRANES · RHEPANOL (PIB)
Bonding Rhepanol is not a matter of spreading arbitrary roof adhesive across a PIB sheet. FDT defines specific products, substrates and methods. The full hfk assembly must be approved for the intended partial or other bonding method.
Identify the exact Rhepanol membrane and substrate first. FDT describes roofing membrane adhesive and Rhepanol adhesive 90 for specified hfk installations, together with distinct contact and dispersion adhesives for particular junctions. Field and upstand adhesive are not necessarily the same product. Consumption follows the approved method and current data sheet.
Which assembly may be bonded?
FDT describes partially bonded hfk configurations over approved substrates. Bonding is part of the wind-uplift roof design; fleece backing does not make every glue or every insulation board suitable.
Distinguish roof-field bonding from details. With hfk the seams, edges and any complementary attachment remain system-specific.
FDT roofing membrane adhesive and Rhepanol adhesive 90
FDT lists roofing membrane adhesive for strip bonding compatible fleece-backed sheets and adhesive 90 for selected bases, including certain existing synthetic roofing membranes. That does not make adhesive 90 universal for all retained roofs.
Specify the exact product, pack and approved substrate. For refurbishment, identify the old membrane and moisture condition using the renovation guide.
Do not substitute generic EPDM contact glue or PVC bonding adhesive without a documented FDT approval.
Upstands and details need separate adhesives
FDT also supplies contact adhesive for particular junctions. Two-sided contact bonding on a vertical upstand can use a different rate from strip bonding over the field. Keep upstands and horizontal contact strips separate.
Estimate vertical area as length × height, then add horizontal bonding where the detail requires it. The geometry method in our edge calculation guide may help, but Rhepanol accessories remain specific to FDT.
An 8 m upstand at 0.25 m height has 2.0 m² vertical surface. Adhesive requirement cannot be finalised without FDT rates and whether one or both surfaces are coated.
Consumption, packs and purchase costs
Use the supplier-approved kg/m² or prescribed stripe method, then calculate the relevant area and round to full containers. Separate any usable stock.
For illustration only, 15 m² at an assumed 0.3 kg/m² equals 4.5 kg. This is not an FDT product rate. Verify the actual instructions, application temperature and pack size, then include labour and materials in the cost estimate.
DakCalc marks the FDT adhesive cost incomplete until a matching product, rate and purchase price are entered.
Pre-installation checks
Check membrane ID, suitable dry substrate, temperature, cleaning, primer when needed, working time, bonding stripes, pressure and chemical compatibility. A test area and wind calculations may be required.
Consider mechanical attachment if bonding cannot be shown suitable for the selected roof assembly. Record the approved method on the job plan.
Estimate Rhepanol roof area, rolls and materials
Select PIB (Rhepanol), verify the hfk roll format and enter actual supplier purchase prices. DakCalc provides a provisional material estimate, not an approved laying plan, wind design or FDT system certification. Verify the delivered hg roll format and configuration.
Open the DakCalc calculator →More Rhepanol guides
Also useful in the knowledge hub: roofing system comparison, calculating membrane laps, roof-edge trims and corners.
Frequently asked questions
Which adhesive suits Rhepanol hfk?
It depends on the FDT assembly and substrate. Roofing membrane adhesive and Rhepanol adhesive 90 are not universally interchangeable.
Are field and upstand adhesives the same?
Not necessarily. FDT has separate field and contact-bonding products for specified applications.
Can I assume 0.3 kg/m²?
No. It is merely an illustrative arithmetic rate, not a universal Rhepanol specification.
Sources and technical documents
Product dimensions, adhesives, fixing methods and examples do not certify a roof assembly. Check current FDT/QRS guidance, local rules, project-specific wind design and your supplier quote before ordering.